Irrigation Accessories

Replenishment part for custom hose starter kit.
ColorStorm-Professional Rubber Hose is made from EPDM rubber for a "crackless" hose cover that is resistant to abrasion, weathering and kinking.

Extra length- 48", Standard hose thread. Add a water breaker and shutoff to complete assembly.

Multi-level throw, approximately 24o Standard Inlet: 3/4" NPT male Operation pressures: 10 to 35 psi Multi-level throw, approximately 24 degrees Standard Inlet: 3/4" NPT male. Operation pressures: 10 to 35 psi. Diameter of throw 40.5'- 49' depending on PSI and height above crop. Flow rate of 1.85-3.38 GPM based on PSI

This unique design provides extremely uniform coverage over a large diameter at low pressures with low evaporative losses. Only one moing part. Constructed entirely of engineering-grade thermoplastics for long-lasting performance. Two year warranty on materials, workmanship and performance. Five year warranty on orifice nozzle wear. Multi-level throw, approximate angle:10 degrees Operation pressures: 15 to 40 psi (1.0 to 3.0 bar) Stream heights range from 1.5 - 3.0 ft above nozzle based on pressure and nozzle size. Diameter of throw 34'-43' depending on pressure and height above crop. Flow rate of 1.30-2.14 GPM based on PSI. Standard inlet: 1/2" NPT male

Standard hose thread. Add a water breaker and shutoff to complete assembly.

Standard hose thread. Add a water breaker and shutoff to complete assembly.

Extra length, and curved to make watering overhead baskets a snap. Standard hose thread, add a water breaker and shutoff to complete assembly.

Water your plugs or seedlings with the softest full-flow watering nozzle available. The 1000PL Red Head Water Breaker has over 1000 micro holes that create an ultra-soft flower shower which will not disturb delicate soil or harm tender plants. Made in the USA from ABS plastic and stainless steel. Weight 1.6 oz. GPM = 7 @ 40 PSI

Water your plugs or seedlings with the softest full-flow watering nozzle available. The 1000PL Red Head Water Breaker has over 1000 micro holes that create an ultra-soft flower shower which will not disturb delicate soil or harm tender plants. Made in the USA from ABS plastic and stainless steel. Weight 1.6 oz. GPM = 7 @ 40 PSI

The Seedling Nozzle allows you to water fragile plants, delicate seedlings or plant cuttings. This high-quality nozzle produces an extra fine hollow "cone mist pattern" and sprays a 1/2 gallon of water per minute. Made in the US from solid brass with 3/4" hose threads.

Multi-level throw, approximate angle:0 degrees. Operation pressures: 15 to 40 psi (1.0 to 3.0 bar) Diameter of throw- 30.6'- 37.4' depending on PSI and height above crop. Flow rate of 1.67-2.78 GPM based on PSI. Standard inlet- 1/2" MIPT.

Water your plugs or seedlings with the softest full-flow watering nozzle available. The 1000PL "Red Head" Water Breaker has over 1000 micro holes that create an ultra-soft flower shower which will not disturb delicate soil or harm tender plants. Made in the USA from ABS plastic and stainless steel.

The 400PL Water Breaker provides fast, full-flow watering without damage to your plants. Patterned after the original 400 Aluminum Water Breaker with 3/4" hose threads, to 400PL is made from high-impact ABS plastic and aluminum to provide a lightweight alternative.

The original full-flow shower head nozzle. The aluminum 400 Water Breaker provides fast, full-flow watering without damage to your plants. Used by professional growers worldwide. Cast aluminum with 3/4" brass hose threads. Manufactured in the USA since 1945. Weight 5.1 oz. GPM = 11.1 @ 40 PSI

The 170AL Water Breaker is excellent for watering in areas with low water pressure or with systems which restrict total water volume. It is designed for small containers (hanging baskets), and when using fertilizer syphons. Adjust water flow to 50% of its volume. Cast aluminum with 3/4" hose threads. Weight 1.6 oz. GPM = 7 @ 40 PSI

The 750 Lemonhead Water Breaker is designed to offer a lower, softer flow. Even softer than the 1000PL Red Head. The 750PL allows for more precise watering and give growers yet another choice for more flexibility in watering. Weight 1.6 oz. GPM = 7 @ 40 PSI

Simply the best shut-off valve available. Dramm's #300 Brass Shut-Off Valve provides fingertip water control at the end of your greenhouse hose. A quarter turn of the large ergonomic handle and the water is off. Full water flow design. Made in the USA from brass, durable seals and a hard chrome plated ball to provide years of service. 3/4 threads.

The Brass Hose Swivel is a live swivel that allows for unencumbered movement between the hose and attachements under pressure. Reduces hose twisting.

standard hose thread- add a water breaker and shutoff to complete assembly

Multi-level throw, approximately 24o Standard Inlet: 3/4" NPT male Operation pressures: 10 to 35 psi Multi-level throw, approximately 24 degrees Standard Inlet: 3/4" NPT male. Operation pressures: 10 to 35 psi. Diameter of throw 40.5'- 49' depending on PSI and height above crop. Flow rate of 1.85-3.38 GPM based on PSI

Standard hose thread- add a water breaker and shutoff to complete assembly.

*Easily and accurately applies fertilizers and other liquids to gardens, container plants and greenhouse crops
*Attaches to standard hose fittings
*Prevents backflow if pressure should fail
*Plastic body for durability Minimum operating pressure 25 PSI (Do not use with more than 50' of hose)
*90 day warranty

The 74 Shut-off valve is made from glass filled polypropylene to be very durable and corrosion resistant. The 74 is lightweight and offers a full flow.